logo
オンラインサービス

How to Judge Sinking Agarwood Grade When Buying in Bulk

2026/11/18

~に関する最新の会社ニュース How to Judge Sinking Agarwood Grade When Buying in Bulk

Direct answer: Sinking grade is a density test, not a quality certificate. A piece sinks when its resin load is heavy enough to displace its own weight in water. For bulk buying that only means something if you test the same lot the factory will actually ship, at the same moisture level, on a cut face rather than a polished or oiled surface — and if the supplier can repeat that lot on your second order.

What does "sinking grade" actually measure?

Agarwood is wood that has been infiltrated by resin. Sound wood floats; resin is denser than water. So the sink test is a crude but honest proxy for resin load per unit volume.

Two things make it crude:

  • Moisture. Freshly cut or recently soaked wood sinks more readily than wood that has equilibrated in a dry warehouse. A lot that sinks in Guangzhou in June can float in Riyadh in December.
  • Surface treatment. Polished, waxed or oil-rubbed surfaces seal pores and change buoyancy. This is the single most common way a sample over-performs.

This is why professional buyers treat the sink test as a screening step, then confirm with a burn test and a lab report before committing to a container.

How do you test a bulk lot without a lab on site?

A workable protocol for one afternoon:

  1. Cut the sample first. Ask for a fresh cross-section on at least three pieces per grade. Test the cut face, not the outside.
  2. Condition the wood. Let the sample sit in the destination climate for 24–48 hours, or dry it gently. Test what you will actually receive, not what arrived wet.
  3. Weigh in water, don't just watch it. A kitchen scale and a beaker give you a specific gravity reading. Watching a piece float or sink tells you a binary; weighing tells you how close to the boundary it sits.
  4. Burn 0.3–0.5 g on charcoal. Resin-rich wood foams, beads oil on the surface and leaves a lighter ash. Resin-poor wood chars and smells of smoke and paper.
  5. Compare against a reference you trust. Keep a sealed reference piece from a previous good lot. Scent memory is unreliable across weeks; a physical reference is not.
  6. Ask for the lot number in writing. If the answer is "same as the sample, don't worry", you are not buying a lot — you are buying a hope.

What do the grades mean in practice?

Trade term Behaviour in water Resin load What it is normally used for
Floating / A grade Floats high, even when pressed under Light, oil lines visible but sparse Incense powder blends, beads at entry price points, room scenting
Half-sink (半沉) Hovers, sinks slowly when pushed Medium, clear oil-line network Daily burning, mid-tier beads, bakhoor base material
Sinking (沉水) Sinks within seconds, unaided Heavy, dense oil lines across the face Premium burning, attar-grade material, high-grade beads
Deep sinking Sinks fast, near-black, minimal white wood Very heavy, resin dominates the cross-section Collector pieces, high-concentration oil, small carved objects

A practical note from our own grading bench at the Conghua base: the difference between half-sink and sink is usually obvious in the hand — sink-grade pieces feel cold and heavy for their size, and the cut face shows resin filling the fibre rather than sitting in lines between it.

Does sink grade matter equally for every product?

No — and this is where buyers overpay.

  • For oil, sink grade is a strong indicator of yield per kilogram, because you are buying resin, not wood. Distillation economics track resin load almost directly.
  • For beads, sink grade matters for density, colour uniformity and the way the bead takes a polish. A 10 mm bead cut from sink-grade material is a different product from one cut from floating wood, even if both look dark on a screen.
  • For incense powder, sink grade is often wasted money. A well-blended half-sink powder with clean oil lines can carry a room; the very top grades are better sold as pieces than ground up.

What are the red flags in a sinking-grade offer?

  • The sample sinks but the offer sheet does not state grade band, lot number and moisture basis.
  • No third-party lab report. We test all product lines through CMA / CNAS / ILAC-MRA accredited laboratories and hold reports for incense, powder, sandalwood and oud oil — a supplier shipping sinking-grade material in bulk should be able to show something equivalent, plus an EU SDS for any oil or fragrance compound in the shipment.
  • The price is far below the market for the grade. In this category, a bargain on sink-grade wood is almost always a bargain on a different grade.

What should a bulk buyer ask before paying a deposit?

Ask for four things in one message: the grade band definition in writing, the lot number that will ship, a 100–200 g conditioned sample from that lot with a fresh cut face, and the lab report reference. A factory with its own material line and processing answers all four without escalating to a manager.

Longsheng has grown and processed agarwood since 2009 from a near 1,000-mu plantation and supporting factory in Conghua, Guangzhou, with raw material graded in-house across the HN-001 to HN-012 Hainan range at a 5 kg minimum per grade. Grading is quoted per specification and lot, not per catalogue label, because the lot is what the scent depends on.

FAQ

What density makes agarwood sink in water?

Above roughly 1 g/cm³, which means the resin has displaced enough air and wood fibre that the piece is denser than water. Because moisture and shape both shift the reading, buyers should test conditioned samples on a cut face rather than polished showpieces.

Is sinking grade always better agarwood?

No. Sink grade indicates resin density, not scent quality or species. A well-formed half-sink piece with clean oil lines can outperform a dense but poorly formed sinking piece in the burner, and for powder applications the top grade is often wasted.

How much sample should I ask for when buying bulk?

100–200 g per grade from the actual shipping lot, conditioned in your own climate for 24–48 hours, with at least three fresh cut faces. That is enough to test buoyancy, burn behaviour and colour consistency without asking the factory to open a full bale.

Can sinking grade be faked?

It can be imitated. Soaking, waxing, oil-rubbing and resin impregnation all raise density, and polished surfaces hide the tell. Cut the sample, condition it, weigh it in water, and burn a small piece — treated wood usually shows an acrid or chemical note and leaves a hard residue.

Why does the same grade smell different between lots?

Because resin chemistry varies with tree, induction method, age and fermentation. In our own production, the same water-distillation and microbial fermentation process (3–6 months of natural aging) produces three distinct floral profiles from different raw-material batches — proof that grade and scent are separate variables.

Do I need CITES documents for sinking-grade agarwood?

For cross-border movement of Aquilaria material, yes — a CITES export permit from the origin country is normally required, and plantation origin is easier to document than wild collection. Buyers importing into the Gulf should expect the permit to be the slowest document in the set.

What MOQ applies to graded raw material?

Our Hainan raw material range is quoted from a 5 kg minimum per grade, and small-lot oud oil from 12 g, so a buyer can grade-test a real lot before committing to volume. Exact figures are quoted per specification and destination.